Ah, moving for the best apparently :D
This airport typo still eludes me. A flight from KMRY to KTVL shows "KMRZ", and the flight from KTVL to KMRY shows "KMRY". I haven't seen any KMRZ lurking in any of the files, it's weird. And P3D reports KMRY normally so I don't think it's coming from there. I had that problem in a previous installation, and it's still there after reinstalling everything from scratch.
Finally, I often have a flap penalty, for ex. in the B-377 stratocruiser I had "You have exceeded the flap speed limit by 11.57kts (-115)". It doesn't show the actual KIAS that was supposedly recorded, but I'm pretty sure I never went over 150 kts during take-off or landing, and for this particular model the aircraft.cfg has damaging-speed at 170 for [Flaps.0] (manual mentions lowering flaps at 188 KIAS to help lower speed). I've seen posts where prop aircraft flaps would also be affected by the [contact_points] section, but I have no idea how and whether it's true. Any clue how I could fix those speeds in FSPassengers, or what I'm misinterpreting? Is there a place where I can actually see the expected speed limit?
[Flaps.0]
type= 1
span-outboard= 0.500
extending-time= 25.000
system_type= 0
damaging-speed= 170.000
blowout-speed= 200.000
lift_scalar= 1.000
drag_scalar= 1.000
pitch_scalar= 1.000
flaps-position.0= 0.000, 0.000
flaps-position.1= 5.000, 0.000
flaps-position.2= 10.000, 0.000
flaps-position.3= 15.000, 0.000
flaps-position.4= 20.000, 0.000
flaps-position.5= 25.000, 0.000
flaps-position.6= 30.000, 0.000
flaps-position.7= 35.000, 0.000
flaps-position.8= 45.000, 0.000
flaps-position.9= 45.000, 0.000
[Flaps.1]
type= 2
span-outboard= 0.9
extending-time= 10
system_type= 3
damaging-speed= 999
blowout-speed= 999
lift_scalar= 0
drag_scalar= 200
pitch_scalar= 0
flaps-position.0= 0
flaps-position.1= 0.0001
flaps-position.2= 0.0002
flaps-position.3= 0.0003
flaps-position.4= 0.0004
flaps-position.5= 0.0005
flaps-position.6= 0.0006
flaps-position.7= 0.0007
flaps-position.8= 0.0008
flaps-position.9= 45
This airport typo still eludes me. A flight from KMRY to KTVL shows "KMRZ", and the flight from KTVL to KMRY shows "KMRY". I haven't seen any KMRZ lurking in any of the files, it's weird. And P3D reports KMRY normally so I don't think it's coming from there. I had that problem in a previous installation, and it's still there after reinstalling everything from scratch.
Finally, I often have a flap penalty, for ex. in the B-377 stratocruiser I had "You have exceeded the flap speed limit by 11.57kts (-115)". It doesn't show the actual KIAS that was supposedly recorded, but I'm pretty sure I never went over 150 kts during take-off or landing, and for this particular model the aircraft.cfg has damaging-speed at 170 for [Flaps.0] (manual mentions lowering flaps at 188 KIAS to help lower speed). I've seen posts where prop aircraft flaps would also be affected by the [contact_points] section, but I have no idea how and whether it's true. Any clue how I could fix those speeds in FSPassengers, or what I'm misinterpreting? Is there a place where I can actually see the expected speed limit?
[Flaps.0]
type= 1
span-outboard= 0.500
extending-time= 25.000
system_type= 0
damaging-speed= 170.000
blowout-speed= 200.000
lift_scalar= 1.000
drag_scalar= 1.000
pitch_scalar= 1.000
flaps-position.0= 0.000, 0.000
flaps-position.1= 5.000, 0.000
flaps-position.2= 10.000, 0.000
flaps-position.3= 15.000, 0.000
flaps-position.4= 20.000, 0.000
flaps-position.5= 25.000, 0.000
flaps-position.6= 30.000, 0.000
flaps-position.7= 35.000, 0.000
flaps-position.8= 45.000, 0.000
flaps-position.9= 45.000, 0.000
[Flaps.1]
type= 2
span-outboard= 0.9
extending-time= 10
system_type= 3
damaging-speed= 999
blowout-speed= 999
lift_scalar= 0
drag_scalar= 200
pitch_scalar= 0
flaps-position.0= 0
flaps-position.1= 0.0001
flaps-position.2= 0.0002
flaps-position.3= 0.0003
flaps-position.4= 0.0004
flaps-position.5= 0.0005
flaps-position.6= 0.0006
flaps-position.7= 0.0007
flaps-position.8= 0.0008
flaps-position.9= 45