23-08-2005, 03:55 PM
Okay...figure this one out...
I get this in the editor:
Well, I fire up FS and this is what I get...
And this is the weight/balance section of the config file...
I'm quite confused on this one...any ideas? And yes, the image for the payload is the correct size...thought of that one already. And yes,
I tried deleting the payload areas and making them with FSP, still no go.
Besides the images being off, I can't load any passenger or cargo. Just fuel.
Post Edited ( 08-24-05 07:41 )
I get this in the editor:
Well, I fire up FS and this is what I get...
And this is the weight/balance section of the config file...
Quote:[WEIGHT_AND_BALANCE] //DC10 Series 30
max_gross_weight= 558000.00 //Design gross weight (ramp) 558,000 lb (260,820 kg)
empty_weight= 238036.00 //Maximum takeoff weight 555,000 lb (259,459 kg)
reference_datum_position=0.00, 0.00, 0.00 //Design landing weight (1) 411,000 lb (182,766 kg)
empty_weight_CG_position= -1.23, 0.00, 6.00 //Maximum zero fuel weight 391,000 lb (166,924 kg)
station_load.0="180, 89.221, -2.267, 9.7, Pilot"
station_load.1="180, 89.221, 2.267, 9.7, Co-Pilot"
station_load.2="180, 85.497, 2.267, 9.7, F/E"
station_load.3="360, 77.024, 0.000, 9.7, Crew 1"
station_load.4= "8316, 64.000, 0.000, 9.7, Zone A"
station_load.5="8316, 53.000, 0.000, 9.7, Zone B"
station_load.6="8316, 42.000, 0.000, 9.7, Zone C"
station_load.7="8316, 31.000, 0.000, 9.7, Zone D"
station_load.8= "8316, 20.000, 0.000, 9.7, Zone E"
station_load.9= "14360,9.000, 0.000, 9.7, Zone F"
station_load.10= "14360,-2.000, 0.000, 9.7, Zone G"
station_load.11= "14360, -13.000, 0.000, 9.7, Zone H"
station_load.12="10142, -24.000, 0.000, 9.7, Zone I"
station_load.13="8316, -35.000, 0.000, 9.7, Zone J"
station_load.14= "8316, -46.000, 0.000, 9.7, Zone K"
station_load.15= "15000,48.500, 0.000, 1.6, Fwd Lower Cargo"
station_load.16= "15000, -30.000, 0.000, 1.6, Aft Lower Cargo"
station_load.17= "500, -51.733, 0.000, 2.5, Bulk Cargo"
//Over all payload above minus crew = 142544 lb
max_number_of_stations = 50
empty_weight_pitch_MOI=12229499 //FAA landing field lgth-std.wght 5,960 ft(1,758 m)
empty_weight_roll_MOI=4035153 //Design range (2) 5,860 mi
empty_weight_yaw_MOI=11280172 //5,096 nmi
empty_weight_coupled_MOI=0.00 //9,429 km
// (1)Higher weights are available.
//(2)277 passengers and baggage; domestic reserves.
// Passenger Capacity 250-380
CG_FORWARD_LIMIT=5.58
CG_AFT_LIMIT=1.265
I'm quite confused on this one...any ideas? And yes, the image for the payload is the correct size...thought of that one already. And yes,
I tried deleting the payload areas and making them with FSP, still no go.
Besides the images being off, I can't load any passenger or cargo. Just fuel.
Post Edited ( 08-24-05 07:41 )