FsPassengers Forums
P3D 3.4 Released - Printable Version

+- FsPassengers Forums (http://www.fspassengers.com/forum)
+-- Forum: Flight Simulators (http://www.fspassengers.com/forum/forumdisplay.php?fid=7)
+--- Forum: Prepar3D General (http://www.fspassengers.com/forum/forumdisplay.php?fid=8)
+--- Thread: P3D 3.4 Released (/showthread.php?tid=17869)

P3D 3.4 Released - sturag - 19-09-2016

Have anyone tried out FSpax on 3.4?

RE: P3D 3.4 Released - Kebas - 19-09-2016

Unfortunately it is not working with version 3.4
Hoping on an update from FSPax soon!

RE: P3D 3.4 Released - djvagelis80 - 19-09-2016

i hope also....very very soon....

RE: P3D 3.4 Released - Joeflyer - 20-09-2016

I hope there aren't any issues with FsP again Wall I didn't even update to 3.3 yet lol

At any rate, I don't plan to update the Client and any other module to get to 3.4. I intent to do a full installation. It seems to work out better that way.

RE: P3D 3.4 Released - Kebas - 20-09-2016

(20-09-2016, 02:51 AM)Joeflyer Wrote: I hope there aren't any issues with FsP again Wall I didn't even update to 3.3 yet lol

At any rate, I don't plan to update the Client and any other module to get to 3.4. I intent to do a full installation. It seems to work out better that way.

Unfortunately it is not working Joe, either after updating the modules apart and after updating with a full installation!! Hunappy
In both situations I get the next errors:

[Image: pSrvckI.jpg]

[Image: YowAAdb.jpg]

Do you inform Dan about this??

Regards,
Jacob.

RE: P3D 3.4 Released - Joeflyer - 20-09-2016

Kebas, I can't view the pics from this work laptop but I got your message and feared this would happen. Yes, I have emailed Dan about it.

RE: P3D 3.4 Released - briansommers - 20-09-2016

(20-09-2016, 01:57 PM)Joeflyer Wrote: Kebas, I can't view the pics from this work laptop but I got your message and feared this would happen. Yes, I have emailed Dan about it.

Thanks, hoping for an update. Can't fly without FSPassengers!

RE: P3D 3.4 Released - Joeflyer - 20-09-2016

Brian, send Dan an email as well. Hopefully he will work on an update soon.

For anyone else wanting to comment about FsP not working with the new update, email Dan right away.

RE: P3D 3.4 Released - briansommers - 20-09-2016

Will do..

RE: P3D 3.4 Released - Joeflyer - 20-09-2016

I just received a reply from Dan. He will be working on an update ASAP. The update should be completed in about a week.

RE: P3D 3.4 Released - Bungegalt - 20-09-2016

I do not know where I should write this. I gladly pay for adons and rarely complain...  a while ago I bought FSpassanger to FSX-SE and I praise the program, unfortunately, I could not use FSpassanger much because it was too much trouble with FSX-SE, so I recently bought P3D instead, which works well. But as I understand it, I have to buy FSpassenger again !! ?? Seriously! Is it a complete new FSpassanger for P3D?

RE: P3D 3.4 Released - Joeflyer - 20-09-2016

(20-09-2016, 06:55 PM)Bungegalt Wrote: I do not know where I should write this. I gladly pay for adons and rarely complain...  a while ago I bought FSpassanger to FSX-SE and I praise the program, unfortunately, I could not use FSpassanger much because it was too much trouble with FSX-SE, so I recently bought P3D instead, which works well. But as I understand it, I have to buy FSpassenger again !! ?? Seriously! Is it a complete new FSpassanger for P3D?

You didn't try to figure out why FsP wasn't working well with -SE or come to the forums to work through a solution?
I don't know how often you have tried perusing the FsP web site, but FsP for P3D had to be recoded to work with FsP, so yes, you would have to pay for the P3D version. If you contact Dan, he may offer you a rebate. Use the Contact tab at the bottom of the page to send him an email.

RE: P3D 3.4 Released - briansommers - 21-09-2016

This is good news about the update.